Fall Protection

Our Manhole Guard Rail* is constructed of strong, one inch tubular .078 gauge steel that is powder-coated in safety yellow for a durable finish and high visibility. Simple one-piece construction offers easy, no-tools assembly. Rail locks open and two hooking chains provide protected entry and exit. For safety, the rail accommodates signs, flags or lights, and for convenience, it can be used with a guard rail tent, umbrellas or winch.

This assembly is to be used as a ‘Temporary Barrier Railing’ only. See OSHA 1910.146©(5)(ii)(B)

WEB CROSS ARM STRAP, O-RING/D-RING, 8’

Anchorage/Tie Off, 1-3/4In x 16Ft, 2 D-Ring

Rope Lifeline, 5/8In x 100Ft, Double Locking Snap One End, Crown Splice Other End

Pillow-Flex harness and 3 D-rings with padded leg straps.

Squids 3700 Web Tool Tether Attachments (6-Pack) act as a retrofit attachment point on tools, belts, harnesses or structures that can be used to tether small hand tools up to 2lbs // 0.9kg and prevent dropped or falling objects from occurring on the job.

Built for secure attachment to tools, this anchor attachment is made of heavy-duty nylon webbing and high-tensile strength nylon thread. Both ends feature a reinforced double stitch web catch for a more durable stop. Once the base of the tail is securely taped to the tool or anchor point, the plated D-ring acts as a captive hole for tethering tool lanyards.

For best use, tape the loop end of the tool tail with Squids Self-Adhering Tape. Available in three sizes: short, medium, long, x-long and 2X-long. When working at-heights, it’s essential to tether your tools. Fall protection lanyards and tethers are pieces of safety equipment designed to attach one end securely to a fixed anchor point, and the other to an appropriate attachment point on a tool by proper tethering.

Positioning Harness, Pass Through, XL 3 D-Ring

DESCRIPTION: The US-96960 Lifeline System is designed for use as an anchoring means for up to 2 persons, used where fall protection and horizontal mobility are required. Per OSHA regulations, horizontal lifelines shall be designed, installed, and used under the supervision of a qualified person as part of a complete personal fall arrest system with a minimum safety factor of 2. Qualified person is defined as follows:

“..one who, by possession of a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and experience, has successfully demonstrated his ability to solve or resolve problems relating to the subject matter, the work, or the project.”

Refer to applicable national standards, including ANSI Z359.1, local, state and federal (OSHA 1910.66 & 1626.502) requirements, for additional information on personal fall arrest systems.

SYSTEM REQUIREMENTS: When ready to use the horizontal system, one must consider the following:

Personal Fall Protection: Use only OSHA /ANSI approved equipment.
Anchorage Points: Must be rigid and allow for a 2:1 safety factor or 5000lbs MBL.
Fall Distance: Measure the distance between working levels and lower levels, to allow adequate clearance for the system to function properly and not to come in contact with an obstruction and/or lower level. To avoid swinging or a pendulum effect, always work under your anchor point.

ALWAYS INSPECT ALL EQUIPMENT BEFORE EACH USE!!!!

• Anchorage: The anchorage to which this product is attached must be capable of sustaining a static load in the direction applied by the personal fall arrest system of at least 3600 lbs. with certification of a qualified person or 5000 lbs. without certification. When more than one personal fall arrest system is attached to the same structure, the strength requirements stated above must be multiplied by the number of personal arrest systems attached to the structure.
• Plan your personal fall protection system. Before installing and using this equipment, consider all factors affecting your safety during use of this equipment.
• Warnings and instructions must be read and understood before using equipment.
• Equipment must be used by trained personnel only.
• Users must understand all OSHA regulations, ANSI standards, and other relevant regulations and standards pertaining to fall protection equipment.

Give your crew the perfect blend of safety, quality, and long-lasting value with 3M™ Protecta® 100% Tie-Off Shock Absorbing Lanyards with Snap Hooks, which offer the freedom and peace of mind your workers value when working at height. Our shock-absorbing lanyards feature a lightweight, stretchy design that expands and contracts (6 ft. to 4.5 ft.) as you move, stretching with you as you work so you can go after each task with more comfort and confidence.